Unit includes: Amplifier, Mounting hardware, and Instruction manual
KICKER® PX-Series Amplifiers are full of advanced technology. PX Amplifiers are specially designed to deliver tremendous power in a tiny, weatherproof footprint, all while requiring minimal power from your charging system. Their compact size and efficiency make them perfect for sand-rails, motorcycles, and even jet ski's! With auto turn-on options, built-in crossovers and flexible input styles, KICKER® amps give you the custom sound you need.
Unbelievable power in a tiny package!
PX Amplifiers are no strangers to the KICKER® tradition of compact size. With as much as 500 watts of power, the only thing small about these amps is their footprint. Made to fit nearly anywhere, these miniature power plants start at under five inches in total width.
Whether it's a a car, side-by-sides, motorcycle, or personal water-craft a small amplifier is what you want, but good is it without weatherproofing. The PX-Series amplifiers feature a weatherproof wiring harness, moisture-resistant circuit board and aluminum casing.
Kicker PXA200.2 200 Watt 2-Channel Class D Car Amplifier
PX Series 200 Watt RMS Two-Channel Class D Amplifier
Conformal coated circuit board suitable for marine or ATV applications
Amplifier is ideal for motorcycles and other vehicles where conventional amplifiers will not fit
Extruded aluminum heat sink design
Speaker and RCA low level Inputs for easy integration with factory and aftermarket audio systems
Two turn on modes: DC-offset signal sense turn-on for easy integration to factory audio systems and conventional 12 volt trigger
Stealth bottom mounted access panel for crossover settings
LED power (Blue) and protect (Green) indicators
balanced differential inputs and Fail-Safe Integration Technology eliminate noise from your vehicle's electrical system
3-way protection circuitry (thermal, overload, and speaker short protection)
Vertical mounting optional
Heavy duty aluminum alloy heat-sink
Nickel-plated screw terminals
CEA-2006 compliant amplifier
Requires minimum 10 gauge power and ground wiring for installation
Frequency Response: 10Hz to 20kHz +/- 1.0dB
Signal to noise ratio: 95 dB
Inputs and Outputs:
2 - Nickel-plated RCA high or low level inputs (150 mV - 10 V)
Input Sensitivity Low level: 125mV - 5V
Input Sensitivity High level: 250mV - 10V
Max Power Output:
Total Power Output: 200 Watts
RMS Power Output:
4-Ohms: 25 Watts x 2
2-Ohms: 50 Watts x 2
1-Ohms: 100 Watts x 2
Built in Crossover:
Selectable high pass: 60Hz / 80HZ / 120Hz (12dB/octave)
Overall Dimensions: 1-9/16" (H) x 7" (L) x 3-7/16" (W)
Recommended Fuse: 25 amp
Amplifier Topology Class
Number of Channels
Total Peak Power Output
Total RMS Power Output
Minimum Impedance in Bridged Mode
Minimum Impedance in Un-Bridged Mode
Strappable Power Output
RCA Pre-amp Audio inputs
RCA Pre-amp Audio outputs
150 mV - 10 V
Speaker level inputs
Bass Knob / Remote Gain
Built in Crossover
Recommended Power Wire Gauge
Write Your Own Review
Ask questions receive answers.
Have a question? Go ahead and ask anything. We are here to help.
We show you how to properly wire subwoofers. There are many options with dual and single voice coil subwoofers and they all present different loads to your amplifier. We show you the do's and don'ts!
Learn the basics of an aftermarket car stereo installation. First we walk you through a step by step process of the wiring harness installation, then we show you how to mount the units using a dash kit.
Amplifiers are power hungry devices that are the heart of every car audio system. A power line fuse on your amp is essential because without one you could have a fire if the power wire is accidentally shorted. We show you how to properly wire a fuse at the battery of your vehicle.
We show you how to set the gains on your amplifiers correctly using an inexpensive oscilloscope. Using the DSO Nano V3, we demonstrate what amplifier clipping looks and sounds like. We then demonstrate how to set your system up the right way and prevent these damaging issues.