Discontinued - Pioneer GM-5300T 2-Channel, 760-Watt Max Power Amplifier
Pioneer GM-5300T Product Highlights
Overview
Pioneer GM-5300T 2-Channel, 760-Watt Max Power Amplifier
Technical Specifications
| Manufacturer | Pioneer |
|---|---|
| Part Number | GM-5300T |
| Amplifier Topology Class | No |
| Number of Channels | 2 Channel |
| Total RMS Power at 1 ohm | 0 Watts |
| Total RMS Power at 2 ohm | 0 Watts |
| Total RMS Power at 4 ohm | 0 Watts |
| RMS Output per Channel (x1 at 4 ohms) | 0 Watts |
| RMS Output per Channel (x2 at 4 ohms) | 0 Watts |
| RMS Output per Channel (x4 at 4 ohms) | 0 Watts |
| Total Peak Power Output | 0 Watts |
| Amplifier Bridging | No |
| Minimum Impedance in Bridged Mode | N/A |
| Minimum Impedance in Un-Bridged Mode | N/A |
| Strappable Amplifier | N/A |
| Strappable Power Output | N/A |
| Frequency Response | N/A |
| Signal to noise ratio | 0dB |
| RCA Pre-amp Audio inputs | N/A |
| RCA Pre-amp Audio outputs | No |
| Preamp voltage | No |
| Speaker level inputs | No |
| Gain Control | No |
| Bass Knob / Remote Gain | No |
| Built in Crossover | N/A |
| Cooling Fan | N/A |
| Color | No |
| Warranty | No |
| Recommended Power Wire Gauge | N/A |
| Overall Height | 0 Inches |
| Overall Length | 0 Inches |
| Overall Width | 0 Inches |
| CEA2006 Compliant | N/A |
| UPC Code | No |
Write Your Own Review
Ask questions receive answers.
Have a question? Go ahead and ask anything. We are here to help.
Please login to ask a product question
Installation Videos & Manuals
We show you how to install a complete car audio system. We install a subwoofer, and amplifier, front speakers, rear speakers, and add sound dampening material on the rear deck and in the front doors.
We remove our original amplifier to install two new amplifiers and a DSP processor. This system takes our previous system to the next level. We now have tons of power and full control of the output of our speakers with our DSP processor while suing our factory head-unit!
In this video we show you how to install power distribution, mount and install two amplifiers and redo our fuse holder and power wiring. We also build a complete harness to our factory head-unit without modifying the vehicles wiring and mount our DSP processor to a factory bracket
We show you how to match a subwoofer and amplifier to build the best subwoofer system you can.
We show you how to install an amplifier in a vehicle with a factory amplified audio system.
Amplifiers are power hungry devices that are the heart of every car audio system. A power line fuse on your amp is essential because without one you could have a fire if the power wire is accidentally shorted. We show you how to properly wire a fuse at the battery of your vehicle.
We show you how to wire speakers to your amplifier. We show 2 channel, 3 channel, 4 channel and 5 channel connections.
James shows you how to wire your subwoofers in Parallel or Series, explains the difference between Single and Dual Voice Coils, and teaches you how to calculate the impedance of your system!
We take the challenge and see what kind of system we can put together for under $400.
Confused by what gauge wire to get for your install? Let James show you how to figure it out!
Wire Gauge Chart: http://www.qualitymobilevideo.com/power-ground-wiring-gauge
We show you how to set the gains on your amplifiers correctly using an inexpensive oscilloscope. Using the DSO Nano V3, we demonstrate what amplifier clipping looks and sounds like. We then demonstrate how to set your system up the right way and prevent these damaging issues.
Loading...