Dodge - Radio Interfaces
Car radio replacement radio interfaces allow you to remove your factory radio and install a new factory radio while retaining all of the factory features.
Onstar adaptors - Onstar adaptors allow you to remove your factory radio and install a new factory radio while retaining all of the factoyr Onstar features.
Shop By
-
idataLink Maestro ACC-SP1 Factory chime replacement speaker$24.99- Chime speaker for use with idataLink ADS-MRR Radio Replacement and Steering Wheel Interface module (Required and Sold Separately)
- Required for some vehicles with collision avoidance, lane departure or blind spot detection systems
-
idataLink Maestro ACC-USB-RAM USB Media Hub replacement circuit board for 2013 - 2018 Dodge Ram Trucks$24.99- Retain your center console media hub USB capabilities when you install an after-market radio
- Compatible with select 2013 - 2018 Dodge Ram Trucks
- Plug & Play Harness and requires no modification to factory wiring
-
Metra CHRYSAV Rear Seat Entertainment System Interface for 2008 - 2013 Chrysler, Dodge, and Jeep$29.99- Easily remove the factory radio and re-integrate the factory video rear seat entertainment system into the new radio
- Provides a video input to the factory overhead monitor
- Retains factory control panel video input to the aftermarket radio
- Retains factory back up camera to aftermarket radio
-
idataLink Maestro HRN-HRR-CH1 Radio Replacement and Steering Wheel Interface Harness for 2007 - 2020 Chrysler / Dodge / Jeep / Mitsubishi / RAM / Volkswagen$39.99- Fits select 2007 - 2020 Dodge and Chrysler Vehicles
- Plug-and-Play T-harness for ADS-MRR Interface
- Install and aftermarket car stereo receiver and retain all OEM features and audio system
- Provides inputs and output to aftermarket car stereo receiver (Speaker, Power/Ground, Illumination, and Navigation)
- Displays engine performance data on touchscreen with select Alpine, JVC, Kenwood and Pioneer receivers
-
Metra LC-CHRC-01 Radio Replacement Data Bus interface with Chime Retention Speaker for 2013 and Up Dodge Ram pickup trucks$69.99- Designed for 2013 and Up Dodge Ram pickup trucks
- Provides accessory output for databus signals (12-volt 3-amp capable output)
- Retains R.A.P. (retained accessory power) while doors remain closed so you can continue to listen to the radio until doors open
- Interface is designed to be used with factory non-amplified systems or when removing the amplified audio system
- Retains the 3.5mm AUX-IN jack
- Retains all factory warning chimes with built in speaker
-
idataLink Maestro HRN-HRR-CH3 Radio Replacement and Steering Wheel Interface Harness for 2013 - 2018 Chrysler, Dodge, Fiat and Jeep Vehicles$69.99- Fits select 2013 - 2018 Chrysler, Dodge, Fiat and Jeep Vehicles
- Plug-and-Play T-harness for ADS-MRR Interface
- Install and aftermarket car stereo receiver and retain all OEM features and audio system
- Provides inputs and output to aftermarket car stereo receiver (Speaker, Power/Ground, Illumination, and Navigation)
- Displays engine performance data on touchscreen with select Alpine, JVC, Kenwood and Pioneer receivers
-
Axxess AX-CH013 2004 - and Up Chrysler radio replacement CAN-BUS interface with navigation outputs$77.99- Chrysler, Jeep, Mitsubishi, and Volkswagen complete radio replacement interface for plug-and-play installation of an aftermarket car radio
- Interface is designed for non-amplified models, amplified models, or when bypassing a factory amplifier
- Pre-wired for steering wheel control interface (Sold separately)
- Provides NAV outputs (parking brake, reverse, and speed sense)
-
Axxess AX-ADBOX2 Auto Detect Radio Replacement Interface Control Box$124.99- Easily remove the factory stereo in an otherwise impossible situation and replace it with an aftermarket stereo and retain all of the factory functions
- Provides accessory (12-volt 10-amp)
- Retains R.A.P. (retained accessory power)
- Used in non-amplified audio systems
- Retains chimes
- Retains factory auxiliary input
- Provides NAV outputs (parking brake, reverse, mute, V.S.S.)
-
Axxess AX-ADBOX1 Auto Detect Radio Replacement Interface Control Box$139.99- Easily remove the factory stereo in an otherwise impossible situation and replace it with an aftermarket stereo and retain all of the factory functions
- Provides accessory (12-volt 10-amp)
- Retains R.A.P. (retained accessory power)
- Used in non-amplified audio systems
- Retains chimes
- Retains factory auxiliary input
- Provides NAV outputs (parking brake, reverse, mute, V.S.S.)
-
Axxess AX-CH5-SWC 2013 - and Up Chrysler radio replacement CAN-BUS interface with steering wheel and navigation outputs$139.99- Chrysler, Dodge, Fiat, Jeep, RAM complete radio replacement interface for plug-and-play installation of an aftermarket car radio
- Retains factory audio system and vehicle chimes
- Retains steering wheel controls
- Provides NAV outputs (parking brake, reverse, and speed sense)
- Interface is designed for non-amplified models, or when bypassing a factory amplifier
-
Axxess AX-CH013-SWC 2004 - and Up Chrysler radio replacement CAN-BUS interface with steering wheel and navigation outputs$139.99- Chrysler, Jeep, Mitsubishi, and Volkswagen complete radio replacement interface for plug-and-play installation of an aftermarket car radio
- Interface is designed for non-amplified models, amplified models, or when bypassing a factory amplifier
- Built in steering wheel control interface
- Provides NAV outputs (parking brake, reverse, and speed sense)
Who Bought This Also Bought
My Wish List
Last Added Items
You have no items in your wish list.
Related Articles & Videos
How to install a car stereo
Watch our video and read our blog for step-by-step instructions documenting the installation of a aftermarket car stereo receiver.
QualityMobileVideo Blog
Car Stereo Wiring Guide
Watch our video and read our blog for the proper wiring colors and their definitions. We explain wire-by-wire what these connections do for the installation of an aftermarket car stereo receiver.
QualityMobileVideo Blog